DY25 detects and alerts you immediay where a circuit is open.
You can quickly and easily Locate short circuits,open connections,broken wires,current leaks and even trace wires.
You can also find intermittent circuit problems by flexing wires or connectors and listening for a change in the receiver tone Allowing you general tracing or pinpointing the problem location.It also shows you the direction to the short with its direction indicator,eliminating the guesswork.
PACKING LIST:
DY25 Sender 1 pcs
DY25 Receiver 1 pcs
User manual 1 pcs(in English)
Oxford handbag 1 pcs
Automotive Short Cable Tracker&Open Wire Finder Less Than 42V DC Find Car Short Circuit Wire
This instrument is designed to identify and trace wires or cables without damaging the insulation.
You can also use it in checking for short circuit and loacting open circuit and so on.
There are a Sender and a Receiver included in the instrument.
Specification
1.Wire Tracing
2.Checking for short circuit
3.locating open circuit
4.Wire identification
Multi-function circuit tester
Easily solve your circuit problems
Identify and track lines , find and determine shorts and break points
3 . 5MM head jack increases the listening effect in noisy environment
248 MM long probe hose is more convenient to operate
Function
* Tracing of wires is made possible even inside bundles, conduits, behind panels, under carpets, upholstery, etc
* Easy to use: simply connect the transmitter in series with the circuit or wire under test, (i.e.: in place of a blown fuse, across a connector,in series with an open wire, a light bulb socket, etc.), and scanning the circuit/wire with the tracers flexible probe to find the trouble spot
* 42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems
* Operates on DC voltages from 6 to 42 volts
* Internally protected against power surges and overloads
* 7” flexible probe allows reaching wires in congested places
* Transmitter and Receiver LEDs show open or short circuit conditions
* Adjustable sensitivity for all tracing situations
* No wire piercing required, non-contact technology!
Flexible probe made of 248mm steel wire
Highly sensitive probe
The tester uses advanced sensors for high sensitivity and fast response
Quickly find circuit problems with high precision
Beep alarm
When a circuit breakpoint is detected , the receiver emits a ”beep”soundThe closer the probe is to the breakpoint , the faster the sound isand the higher the volume
LAUNCHER
With two modes can be choose to easily solve circuit problems
Mode : TONE ( Cable Tracking / FindBreakpoint / Cable Identification )
Pull the transmitters open key to Cable Tracking /Find the location of the breakpointcable identication At this time the reLED of the transmitter is on . f the red LED is not lit , check the powerconnection
( Please refer to the manual for the detailed measurement method )
Mode : CONT ( Find short circuit)
Pull the transmitters open key to the ” find short positiorAt this point , the green LED of the transmitter is on . If the greenLED is not lit , check the power connection
( Please refer to the manual for detailed measurement methods)
Sensitivity adjustable
Sensitivity can be adjusted according to the detected environment
External headset connection
When used in a noisy environment , connecting heads candetect circuit problems more quickly
When performing cable breakpoint check , cabletracking and cable identification in a relatively noisyjudgment resuit a 3.5mm plug ear can as ” senvironment . in order to avoid the noise infiuenoIsed for monitoring and judgment
(steps for usage) Before inserting the ear , first adjust thesensitivity of the receiver to the minimum , and theninsert the ear detection to gradually increasethe sensitivity until the ear volume Is moderate
HOW TO USE THE PROBE?
The probe of the Receiver is built of coiled steel and may be bent as needed, in order to reach wires in ongested or difficult areas.
Depending on the circuit characteristic and sensitivity settings, the probe will pick up the signal from the wire in a range of positions.
However,for the best possible range the Receiver’s probe tip (black cap) should be positioned perpendicular (at 90°) to the wire being traced and either above or below it.
PRODUCT DETAIL PRESENTATION
PRODUCT SPEIFICATION
Quickly and easily locate short circuits
Save your times and increase your income
Judge continuty of the cables or wires.
Track the cables or wires, and diagnose the break point
Receive the tone signal on the cables or wires(e line)
Indentify the state in the working e line (clear, ring, busy)
Send a single solid tone or a dual alternating tone to the object cables or wires.
5. We are not responsible for your Customs duty.
1. If items are found in bad condition when received, please contact us freely. We can refund the money or resend a new one to you.
2. If you are not satisfied with the product because of personal preference, you can return it to us within 7 days. You need to pay the freight.
1.12 months warranty
2.If you are not satisfied when you receive your item or with quality problem,please contact us,we can offer return or resend warranty but please offer evidence to show the problem actively.
